User Area
11/04/2024 all 10:00:04 |
Pregi: scrivo ora dopo aver testato l'addolcitore, confermo ottimo prodotto come da descrizione,grazie per ... |
Difetti: |
Voto: 5 |
11/04/2024 all 08:08:59 |
Pregi: ... |
Difetti: |
Voto: 4 |
06/03/2024 all 07:04:13 |
Pregi: Bonjour dommage que la notice ne soit pas en français Cordialement ... |
Difetti: |
Voto: 5 |
How to choose the submersible well pump?
In this website you will find the best range of submersible electric pumps for wells on the market. Below our guide for the correct choice of your electric well pump and of all the other necessary components.
Choosing the right electric pump for your well is not simplistic but just a "drop of common sense" and you're done. There are many reports on water collection from wells. This short guide does not want to replace the opinion of an expert but wants to give an orientation to the choice of the submersible electric pump best suited to your well.
Never forget these 3 factors:
1)Well flow rate (maximum flow rate for drawing water from the well)
2)Energy parameters (Maximum energy supplied by the distributor or generator)
3)Costs (The more powerful the system and the more the price increases)
When an electric pump does not work anymore, look at the plate to base on choosing a pump with the same parameters. But let's make sure to install a submersible pump that is suitable for your needs. Was the flow of the previous electric pump satisfactory? Another important question concerns the use for which the submersible pump is intended.
Uses of Submersible Pumps
1)Pressurization of the water system (increase and maintain the pressure inside the system);
2)Filling a tank;
3)Irrigation.
To maintaining the pressure inside the system high, the management of the submersible pump is automated by using inverter equipment (or on-off device).
In this case you will need to communicate the following information:
- power supply - example 230 Volts single-phase (domestic power supply)
- water needed - example 50 liters per minute *
- well depth (from the free surface of the water) - example 35 meters
- altitude (difference in height from the pit to the lowest point) - example 10 meters
- pressure - example 3 bar = 30meters **
- diameter and type of piping between the submersible pump and the highest point - example 32mm PE PN10AD
- distance between the submersible pump and the highest point - example 65 meters
* if you don't know the flow rate, specify the quantity and type of water points used
To find the most suitable model for your needs, our technical office is at your disposal to advise you on the model of immersion pump that best suits your needs.
Filling a tank with a submersible pump
It is one of the simplest applications. Taking the water from the well to make it flow into a tank and then distribute it by fall, with a pump or through a pressurization unit to the water system.
In this case you will need to communicate the following information:
-
power supply - example 230 Volts single-phase (domestic power supply)
-
water needed - example 50 liters per minute *
-
well depth (from the free surface of the water) - example 35 meters
-
altitude (difference in height from the pit to the lowest point) - example 10 meters
-
diameter and type of piping between the submersible pump and the highest point - example 32mm PE PN10AD
-
distance between the submersible pump and the highest point - example 65 meters
-
type of use - example filling tank, direct irrigation with gardening hose etc
The ideal model is the 4GS07M-4OS single-phase Lowara 1 HP.
Our technical office is at your disposal to advise you on the model that best suits your needs.
Good solution to pump water with suspended sand
The ideal solution for pumping well water with suspended sand are the X-Power watercooled ecological submersible pumps. They are the only pumps able to pump water from deep wells with sand and solid contents up to 450 g/m.cube. They also withstand dry running (due to an accidental lack of water). They are also ecological as they are cooled with water and lubricated by a mixture of aqua and natural glycol.
Submersible pump to be installed inside a tank
To select the right pump, you need the value of the quota and the number of home appliances. The pumps that are used inside the tanks are self-cooled monoblock watercooled submersible pumps. If you want to install a submersible pump with separate motor and pump, you must equip the pump with a special cooling system: See submersible pumps installation inside the tank.
Ultimately...
Ultimately it is important to distinguish whether a pump is used for: to fill a tank, to pressurize a plant, or to irrigate. For example, using the pump to fill a tank needs lower powers than the powers required for boosting.
Our technical office is at your disposal to advise you on the model that best suits your needs.
Lifting system for well with submersible pump and single-phase inverter
The water passage inverter is characterized by the ease of installation and the pressure detection system by transducer. The electric pump is managed by the inverter which controls the submerged pump when the taps are opened and closed (by modulating the power according to actual needs, you will save from 30% to 50% of electricity per year).
Click on the individual elements of the system!
Each table shows the pump model (electric pump code), the power (Kw or Hp), the supply voltage (Volts), the height in meters (H = ml) and its flow rate (l/minute - m3/hour), the delivery time (working days), the price (€ excluding VAT 22%) and the shopping cart.
Practical examples with electric pumps sold on Pippohydro | |||||||
Type of installation |
Application |
Electric pumps (model/s) |
Operation |
Illustration |
|||
Well Cistern |
Garden or domestic water boosting |
Submersible electric pump |
The pump starts in manual on/off mode or by means of a float switch via an electrical panel |
Well Cistern |
Garden or domestic water boosting |
The pump starts in manual on/off mode or by means of a float switch via an electrical panel |
Well Cistern |
Garden or domestic water boosting |
The pump starts in manual on/off mode or by means of a float switch via an electrical panel or with the help of a presscontrol or an active driver inverter |
Well Cistern |
Water pressurization
for irrigation or water supply
|
The pump starts in manual on/off mode or by means of a float switch via an electrical panel |
Well Cistern |
Water pressurization
for irrigation or water supply
|
Caprari submersible pumps (diameter: 140mm) | The pump starts in manual on/off mode or by means of a float switch via an electrical panel |
Well Cistern |
Water pressurization
for irrigation or water supply
|
The pump starts in modulation mode by means of the inverter command |
Shallow well
Cister |
Domestic, garden, irrigation water pressurization |
Submersible pump: SHARKMATIC Developer: X-POWER Variations:2 |
The pump starts automatically according to the water need |
Lake
|
Water boosting for irrigation |
Submersible pump: |
The pump starts automatically according to the water need |
How to choose a well pump?
Lifting system for well with submersible pump and inverter
Connections for submersible pump with water passage inverter
Single-phase submersible pump system with wall inverter
Well water system with submersible pump and presscontrol
Well water system with submersible pump and pressure vessel
Damages and possible problems in water systems
How to install monoblock (close-coupled) pump?
If you are having difficulty in locating something on our website,
please